Installing wallpaper doesn’t have to be overwhelming. These wallpaper installation instructions are designed for both professional installers and DIY projects, covering peel and stick, pre pasted, and commercial Type II wallcoverings printed by Applied Coverings.
Select your material below to view step by step instructions.
Suede Type II 20oz
Step 1: Choosing the Right Adhesive
When working with commercial grade wallcoverings, selecting the proper adhesive is key to a clean installation and future removability. All professional wallcovering adhesives are waterbased, but they vary in formulation and performance.
Clay Based Adhesive
Considered the traditional choice for commercial installations. Clay pastes require more care during cleanup if they contact surfaces outside the wallcovering. For best results, use a natural sponge with clean water to wipe away residue, rinsing frequently.
Clear Adhesive (Cellulose Based)
Easier to clean than claybased pastes, as they tend to dry into a residue that flakes away. They are often preferred around delicate finishes like wood or decorative moldings. A strip of painter’s tape can also act as a barrier on sensitive surfaces.
Strippable Adhesive
Designed for easier removal when it’s time to replace or update the wallcovering. Choosing a strippable adhesive can save time and minimize wall damage during future renovations.
Step 2: Applying Adhesive
Apply the adhesive evenly to the back of each panel using a roller, brush, or pasting machine. Be sure to coat the edges thoroughly. Fold the pasted panel onto itself, adhesive sides together, taking care not to crease the material. Let it rest or book for 5 to 8 minutes to allow the adhesive to activate and soak in.
Important: Only install when the temperature is at least 65°F (18°C) or higher, and keep the room conditioned both before and after installation for best results.
Step 3: Hanging the First Panel
Once the panel feels tacky, it’s ready to apply. Start at the top of the wall, lining the edge with the ceiling. Unfold and press the panel into place.
Use a felt wrapped smoothing tool or plastic squeegee to press the wallpaper firmly against the wall, working outward and downward. This ensures good contact and reduces air pockets.
As you work, immediately wipe away any adhesive that gets on the surface or seams using a damp sponge and clean cloth. Rinse your sponge often in warm water to avoid streaks.
Step 4: Seaming and Additional Panels
Our Type II commercial wallpaper is designed with an overlap system to achieve seamless joints. Each panel typically includes a 1 inch overlap on both sides.
To create a professional seam, place the new panel over the previous one. Using a sharp blade and a straightedge, cut vertically through both layers in the center of the overlap. Carefully remove the excess strip from each panel. Smooth the edges back together to form a tight butt joint.
Repeat this process for each new panel, replacing your blade often to ensure crisp cuts.
Step 5: Trimming and Finishing
After all panels are applied, carefully trim away the excess material along the ceiling, baseboards, and corners using a utility knife with a fresh blade. A ruler or straightedge can help guide precise cuts.
Use the same method to cut neatly around doors, windows, outlets, and other fixtures.
Terralon Smooth Type II
Step 1: Choosing the Right Adhesive
When working with commercial grade wallcoverings, selecting the proper adhesive is key to a clean installation and future removability. All professional wallcovering adhesives are waterbased, but they vary in formulation and performance.
Clay Based Adhesive
Considered the traditional choice for commercial installations. Clay pastes require more care during cleanup if they contact surfaces outside the wallcovering. For best results, use a natural sponge with clean water to wipe away residue, rinsing frequently.
Clear Adhesive (Cellulose Based)
Easier to clean than claybased pastes, as they tend to dry into a residue that flakes away. They are often preferred around delicate finishes like wood or decorative moldings. A strip of painter’s tape can also act as a barrier on sensitive surfaces.
Strippable Adhesive
Designed for easier removal when it’s time to replace or update the wallcovering. Choosing a strippable adhesive can save time and minimize wall damage during future renovations.
Step 2: Applying Adhesive
Apply the adhesive evenly to the back of each panel using a roller, brush, or pasting machine. Be sure to coat the edges thoroughly. Fold the pasted panel onto itself, adhesive sides together, taking care not to crease the material. Let it rest or book for 5 to 8 minutes to allow the adhesive to activate and soak in.
Important: Only install when the temperature is at least 65°F (18°C) or higher, and keep the room conditioned both before and after installation for best results.
Step 3: Hanging the First Panel
Once the panel feels tacky, it’s ready to apply. Start at the top of the wall, lining the edge with the ceiling. Unfold and press the panel into place.
Use a felt wrapped smoothing tool or plastic squeegee to press the wallpaper firmly against the wall, working outward and downward. This ensures good contact and reduces air pockets.
As you work, immediately wipe away any adhesive that gets on the surface or seams using a damp sponge and clean cloth. Rinse your sponge often in warm water to avoid streaks.
Step 4: Seaming and Additional Panels
Our Type II commercial wallpaper is designed with an overlap system to achieve seamless joints. Each panel typically includes a 1 inch overlap on both sides.
To create a professional seam, place the new panel over the previous one. Using a sharp blade and a straightedge, cut vertically through both layers in the center of the overlap. Carefully remove the excess strip from each panel. Smooth the edges back together to form a tight butt joint.
Repeat this process for each new panel, replacing your blade often to ensure crisp cuts.
Step 5: Trimming and Finishing
After all panels are applied, carefully trim away the excess material along the ceiling, baseboards, and corners using a utility knife with a fresh blade. A ruler or straightedge can help guide precise cuts.
Use the same method to cut neatly around doors, windows, outlets, and other fixtures.
Peel & Stick Linen
Step 1: Prepare and Unroll
Unroll each wallpaper panel and place them flat on a clean surface with the printed side facing up. It’s normal to see some bubbles or light creases at this stage. They will smooth out once the wallpaper is installed on the wall.
Important: Avoid installing peel and stick wallpaper on surfaces painted with stain resistant, washable, low VOC, or specialty paints. These coatings are designed to resist adhesion and may prevent the wallpaper from sticking properly.
Step 2: Position the First Panel
Peel back just 6 to 12 inches of the liner at the top of the first panel. Do not remove the entire backing all at once. Correct placement of the first panel is critical for a smooth installation.
Line up the panel with the ceiling or top edge of the wall and press into place. Use a felt wrapped smoothing tool or soft plastic squeegee to secure the top section, working from the center outward. Avoid applying too much pressure, which can scratch the surface.
Continue peeling the backing in small sections (about 4 to 6 inches at a time) while pressing the wallpaper to the wall. A second person can help by holding the lower portion of the panel as you work your way down.
If bubbles appear, gently push them out toward the edges with the squeegee.
Step 3: Hanging Additional Panels
Align the next panel edge to edge with the first, carefully matching the design pattern (butt joint).
In some cases, an overlap may be required (½ to 1 inch). When overlapping, apply the new panel over the edge of the previous one. Installers may choose to use a double cut technique trimming through both layers at once to create a seamless join.
Repeat the same installation method for each additional panel.
Step 4: Trim the Excess
Once all panels are in place, carefully trim off any excess material with a sharp utility knife. Follow the wall edges, ceiling, or baseboards for clean lines. A straightedge or ruler can help maintain precision.
Use the same method to trim around windows, doors, outlets, or other fixtures.
Step 5: Removing Your Wallpaper
To remove, gently peel each panel away from the wall, keeping it as flat and parallel to the surface as possible. This reduces tension and helps prevent wall damage.
For reuse, reapply the panels to their original backing liner to protect the adhesive and preserve stickiness for future applications.
Peel & Stick Canvas
Step 1: Prepare and Unroll
Unroll all panels and lay them flat with the printed side facing up. Allow the material to relax before installation.
Important: Do not apply Peel and Stick Canvas to walls painted with stain resistant, low VOC, or washable paints. These coatings are designed to block adhesion and will prevent proper bonding. For best results, apply only to smooth, clean, and primed wall surfaces.
Step 2: Peel & Stick Installation
Note: Embossed vinyl has a slight texture that adds depth to the print but can stretch if pulled too firmly. Handle with care and avoid letting the adhesive side fold onto itself.
Peel back 3 to 6 inches of the liner at the top of the first panel. Do not remove the entire backing all at once.
Line up the top edge of the panel with the ceiling or starting point on the wall. Press the exposed section into place, smoothing it with a felt wrapped squeegee or plastic applicator. Work outward from the center in overlapping strokes, applying firm but even pressure to push the adhesive into the wall surface.
Continue peeling the liner downward in 4 to 6 inch increments while applying the panel step by step. Having a second person hold the lower portion makes handling easier.
If air pockets appear, use the squeegee to gently press them toward the edges.
Step 3: Installing Additional Panels
Each mural panel is designed with a small overlap (about ½ to 1 inch) to ensure clean seams. Position the next panel so it overlaps the previous one, carefully matching the printed pattern.
Do not butt panels edge to edge. Smooth down the overlap area with the squeegee to secure the seam. Repeat this process for all additional panels.
Step 4: Trimming Excess
After installation, carefully trim away extra material using a sharp utility knife. Follow the ceiling, baseboards, and corner edges for precise results. A ruler or straightedge can be used to maintain straight cuts.
Use the same method to trim around windows, doors, outlets, or fixtures.
Step 5: Removing Peel & Stick Canvas
When it’s time to remove, slowly peel each panel away from the wall, keeping the material as parallel to the wall as possible. If adhesive feels resistant, use a hair dryer or heat gun on a low setting to warm the panel and soften the adhesive for easier removal.
Pre Pasted Wallpaper
Step 1: Activate the Adhesive
To prepare your wallpaper, lightly wet the back to activate the glue. The easiest method is to use a spray bottle or garden sprayer, misting the entire surface evenly, paying special attention to the edges. Allow the panel to rest for 10 to 15 seconds so the adhesive activates.
Optional: For added flexibility, book the panel by folding the pasted sides together (glue to glue) for about one minute. Be careful not to crease the material.
Note: Each panel will expand slightly when moistened. For best results, wet and book every panel for the same amount of time.
Step 2: Apply the First Panel
Begin at the ceiling line, placing the top edge of the wallpaper against the wall. Keep the lower half folded while you position the top portion. Once aligned, gently press the panel into place.
Using a wallpaper smoother or felt wrapped squeegee, work from the center out to remove air pockets. Apply firm, even pressure especially on lightly textured walls to help the adhesive set. Avoid pressing too hard to prevent surface scratches.
Continue unfolding the lower half, smoothing as you go. If bubbles appear, lightly push them out toward the edges. Small bubbles (quarter size or smaller) will usually flatten on their own as the wallpaper cures.
Step 3: Hanging Additional Panels
Line up the next panel edge to edge with the first, carefully matching the pattern. This is called a butt joint.
If an overlap is required (about ½ to 1 inch), place the new panel over the edge of the previous one. Some installers choose to make a double cut, trimming through both layers to create a seamless joint.
Follow the same method from Step 2 to apply and smooth the remaining panels.
Step 4: Trim Excess Material
After all panels are secured, carefully trim away the excess with a sharp utility knife. Follow the ceiling, baseboard, and corner lines for clean edges. Use a straightedge or ruler to guide cuts.
Cutouts around outlets, windows, and doors can be trimmed in the same way.
Step 5: Removing Your Wallpaper
When it’s time for a change, gently peel the panels from the wall starting at one corner. Any leftover adhesive can be wiped away with a damp sponge. Depending on the condition of the painted surface, some touch ups may be necessary.
